Shopping
Autoclave Maintenance
Autoclave Parts
Autoclave Troubleshooting
Dental Equipment Parts
MEDIVATORS
Videos and Animations
EXAM TABLES & CHAIRS
Case Studies
Free Technical Support
Autopsy Saw Parts
Infant Incubators & Warmers
Lab Equipment
Ventilators
Orthopedics & Physical Therapy
Patient Cables & Leadwires
ASPIRATORS AND SUCTION PUMPS
Maintenance Guides
Operational Manuals
Maintenance Tips
Parts Installation Guides
Account Info
Log In
Create Account
Autoclave Maintenance
Tuttnauer Maintenance Guides
Statim Maintenance Guides
Autoclave Parts
Scican Statim
Midmark ® Ritter
Tuttnauer ®
Pelton Crane
Barnstead Sterilizer
Kavoklave
Midmark Ritter
NAPCO
AMSCO
PRESTIGE 2100
Ritter - Castle
Spectroline
S.S. White
Vernitron
Autoclave Cleaning Products
MDT Harvey Mediclaves
Autoclave Repair Supplies
Autoclave Repair Special Tools
Autoclave Troubleshooting
Prestige 2100
Statim G4 Troubleshooting
tuttnauer temp
STATIM DETAILED TROUBLESHOOTING
VernitronTroubleshooting
NAPCO Troubleshooting
How To Test Heating Elements
Midmark Troubleshooting
Tuttnauer Troubleshooting
STATIM TROUBLESHOOTING
Documents & Guides
Pelton Crane Troubleshooting
Troubleshooting Guides
AMSCO 3000 BASIC TROUBLESHOOTING
AMSCO 900 & 901
Delta XL Troubleshooting
Castle Table Top Troubleshooting
CHEMICLAVE 5000 TROUBLESHOOTING
Kavoklave
Steam Trap Troubleshooting
Dental Equipment Parts
Dental Chair Parts
Dental Handpieces & Parts
DENTAL ULTRASONIC SCALERS
Miscellaneous
Dental Compressor Parts
Dental Delivery Systems
Dental Film & X-Ray Processors
Dental Light Parts
Dental Vacuum Parts
Dental Water Control Parts
MEDIVATORS
Medivator Advantage Plus
Medivator DSD-201
Medivator CER Optima
Medivator DSD-91E
Medivator DSD Edge
Medivator SSD-102
More
Videos and Animations
EXAM TABLES & CHAIRS
Case Studies
Free Technical Support
Autopsy Saw Parts
Infant Incubators & Warmers
Lab Equipment
Ventilators
Orthopedics & Physical Therapy
Patient Cables & Leadwires
ASPIRATORS AND SUCTION PUMPS
Maintenance Guides
Operational Manuals
Maintenance Tips
Parts Installation Guides
About Us
Blog
Home
›
Autoclave Parts
›
Tuttnauer ®
›
EZ9 Autoclave Parts
›
EZ9 Parts Installation Guides
› How To Remove and Replace the EZ9 Door Bellows
How To Remove and Replace the EZ9 Door Bellows
The Tuttnauer Door Bellows
Removal & Installation Guide
There are two method of removing the Door Bellows
Method 1 - Compressed air
Tuttnauer Door Bellows Removal
Remove the Brass Housing Bolt from the Door
Locate the hole on the face of the Door that leads to the bellows cavity
Block the opening in the side of the Door where the Housing Bolt was removed with a thick book or block of wood. Care should be taken because the Bellows Assembly will be projected with a great deal of force when using compressed air
Apply air pressure to the hole on the face of the Door The air pressure will blow the Bellows Assembly out of the cavity
Check that the bellows gasket has been removed from the bellows cavity, if not reach into the door with a long thin screwdriver and remove the gasket.
Remove the old bellows from the brass housing
Method 2 - Extraction
Tuttnauer Door Bellows Removal
Remove the Brass Housing Bolt from the Door
Remove the steel locking pin
Using the Bellows Extraction Tool
Part #TUB036-8729
or a 4 inch long drywall screw insert the tool or screw into the bellows assembly until the brass bushing is reached.
Thread the tool or screw into the center hole of the brass bushing one or two turns or until the threads have locked on to the bushing.
Using the tool or screw remove the Bellows Assembly from the Door
Check that the bellows gasket has been removed from the Door, if not reach into the door with the tool or screw and remove the gasket.
Remove the old bellows from the Brass Housing
Tuttnauer Door Bellows Installation
Insert the new Bellows Kit into the Brass Housing
Install the Brass Housing Bolt on to the front of the Housing
Insert the assembly into the Door
Tighten down the Housing Bolt,
it needs only to be snug.