Statim 2000 Units
Identifying Software Versions
To identify a units software version, power it OFF and back ON again
During start up, a number is briefly displayed in the upper right-hand corner of the LCD that indicates which software is installed
This number is also printed on the label attached to the U14 microprocessor and the U8EEPROM device on the Controller Board
Note that units with Revision 3.x or 4.x controller boards WILL NOT display the software revision on the LCD display (These units will display "SELECT A CYCLE" instead os software version)
The software version number is the character to the immediate right of the R
Display on Power-Up
| S503R204 |
S503R204 |
S503R100 is software version 1.00
S503R101 is software version 1.01
S503R102 is software version 1.02 |
S503R204 is software version 2.00 revision 4 |
Microprocessor Label
01-104455
S52O3R204
Jan. XX03 |
EPROM Label
S5202R102
0301
03=Model Year/01=Model Week |
| Model |
Approximate Year of Manufacture |
Software Revision |
Steam Generator Type |
Software Revision |
Pump |
Compressor |
Pressure Transducer |
Validation Thermocouple |
Calibration Procedure |
| 1000 |
1992 - 1995 |
N/A |
Aluminium
Internal |
3.x/4.x |
- |
N/A |
N/A |
N/A |
1 |
| 2000 |
1992 - 1995 |
N/A |
Aluminium
Internal |
3.x/4.x |
- |
- |
N/A |
N/A |
1 |
| 2000 |
1995 - 2005 |
S2O2R1xx
S2O2R2xx |
Aluminium
Internal |
2.x/5.x |
- |
- |
N/A |
N/A |
2 |
| 2000 |
2005 - 2007 |
S2O2R5xx |
Aluminium
Internal |
6.x |
- |
- |
N/A |
- |
3 |
| 2000 |
2007 |
S2O2R6xx |
Aluminium
Internal |
7.x |
- |
- |
N/A |
- |
4 |
| 2000 G4 |
2010 ? |
S2O2R7xx |
Aluminium
Internal |
7.x |
- |
- |
N/A |
- |
8 |
| 2000S |
1995 - 2004 |
S2S2R1xx
S2S2R2xx |
Aluminium
Internal |
2.x/5.x |
- |
- |
-
(60 psi) |
N/A |
5 |
| 2000S |
2004 - 2005 |
S2S2R4xx |
Stainless Steel |
6.x |
- |
- |
-
(68 psi) |
N/A |
6 |
| 2000S |
2005 - 2007 |
S2S2R5xx |
Aluminium
Internal |
6.x |
- |
- |
-
(68 psi) |
N/A |
6 |
| 2000S |
2007 |
S2S2R6xx |
Aluminium
Internal |
7.x |
- |
- |
-
(68 psi) |
N/A |
7 |
| 2000S G4 |
2010 |
S2S2R7xx |
Aluminium
Internal |
7.x |
- |
- |
-
(68 psi) |
N/A |
9 |
Statim 2000 Revision 3.x/4.x type board (1992 - 1995)
Typical features
- Revision number is located on the bottom right hand side of the board
- Single, rectangular microprocessor
- Main fuses (F3 & f4) vertically located above black Hahn Transformer Labeled TEST2)
Statim 2000 Revision 2.x/5.x type board (1995 - 2004)
Typical features
- Revision number located on the bottom right hand side
- Rectangular microprocessor plus EPROM
- "W1" jumper for calibration
- Main fuses (F3 & F4) (Horizontally located to the Left of the Hahn Transformer
- Blue "pressure interface/printer" connector
Statim 2000 Revision 6.x type board (2004 - 2007)
Typical features
- Revision number bottom right hand side
- Square microprocessor plus EPROM
- "W1" jumper for calibration
- Blue "pressure interface/printer connector"
Statim 2000 Revision 7.x type board (2007 to present)
Typical features
- Up to revision 7.30, the revision number is on the top right hand side (printed vertically)
From revision 7.4 onwards, the revision number is on the bottom left hand side (printed horizontally) under the connector J1
- Square microprocessor plus EPROM
- NO "W1" jumper for calibrationM/li>
- NO Blue "pressure interface/printer" connector
- All components integrated on single board
- Surface mount type component
- "Push in" yellow thermocouple connectors
